Видео

I have an xtool d1 pro rotary will that work with this machine?

2:56 unloosen it, lol

not correct cleaning for the lens technique as you can scratch it by rubbing. Should use drag and drop and 95% isopropyl alcohol. The rest is all helpful.

Hello awesome video, we keep getting a frame oversized error any help greatly appreciated thanks much

Hello awesome video, we keep getting a frame oversized error any help greatly appreciated thanks much

Where is the gal with the huge buttie ?

Too fast

This video saved me a ton of time. Settings were not perfect but close enough to give me a good head start. Thank you.

We need a QR code that goes to your TikTok or yt channel!

What tool are you using to produce multiple coasters?

I need it pookie 😘

"Golf is easy"

Are you changing steps per rotation on different containers?

80 or 100w?

❤ how do you find good quality wood that laser cuts nice?

Nice

eu troquei o sensor as luz acende normal mais so que ele nao para o eixo

What cnc router do you have?

Bookmarking your page for those tickets. My boyfriend would love these 😂

😂 love it

'Merica!!

Awesome!!

what's is water and "LA"?

Got half my pinky on one of these cut so clean didn’t notice it

I have had my Monport 20 X 28 60 watt CO2 laser with autofocus for more than a month. I was experiencing jobs stopping before they are completed, and strange behavior with the laser. It will wander off the line when cutting, and then return and finish the cut, but the piece has been ruined. I am having similar problems when engraving. I use Lightburn connected by USB. I understand that using USB can cause problems. I have read that the best way to connect is via ethernet. I ran a network cable from my router to the laser. There is no indication of link or data at the connector. I checked the Admin page in my router to look at the list of connected devices and the laser does not show up. I verified that the network cable is good by connecting a laptop to the network cable. It shows link and data indicators on the laptop. I am also able to see the laptop in the list of connected devices. I set the IP address in the Ruida controller on the laser as recommended. I had intended to do a reserved IP address for the MAC address in laser. Even just plugging in the laser should have generated a DHCP IP address in the router, and I should be able to see it in the list of connected devices in the router. I have contacted Monport support repeatedly, and I get what appears to be an “automated” or “AI” reply that uses some of the words in my support request, but provides no real help. One of the reasons I bought the Monport laser aside from price and good reputation was the promise of US based support. I have called the US Support number, and each time I get a message that the mailbox is full and cannot accept any more messages. It offers me the opportunity to send an SMS message, but I never get a call back. They asked me to send a video of the problem. What is the point of sending a picture of a network port that does not show link or data lights? It’s just a delaying tactic. They asked me to check the software. I am assuming that they mean the firmware in the laser. They do not provide any documentation or procedure, or even what is the most current version of the software. I now have a very expensive laser that I can’t use because it is malfunctioning. It should be very easy for Monport to send a new Ruida controller and I will install it. The delay in getting any kind of a response from them, except the “automated” response is even more frustrating. I am looking into my legal options to return the machine, and get a refund. Since it is past the 30 day window for a return I’m sure they will not be helpful. I intend to contact the Attorney Generals Office in my state to find out what I can do. I don’t expect that anyone on RUclips can help, but I offer this as a caution to anyone who was considering purchasing from Monport.

Hi, Thanks for the vid. Unfortunately I can't hear nor see the settings you did for the Y accelaration box.

Pigment brand ?

💕💕💕💕💕👍👍👍👍🥰🥰🥰🥰🥰✝️🛐🙏🙏🙏🙏☝️☝️☝️☝️😭😭💕💕💕💕💕

good morning @customgrains I am following all the steps as described, but when I hit start and the machine starts engraving, the design is engraving with the height of the design compressed. Ex: my design is W: 3" x H: 6.25" rotated 90 degrees (just like you have it on lightburn). The preview looks fine/normal. But, once it starts engraving, the design is engraving with the Height much smaller than the indicated 6.25", the image is coming out "squished", without any size changes being made on lightburn. any thoughts? @customgrains

Dont mistake the Kingdom of God for America.

Kill music, show results ...🤦‍♀️💀

Are you using a 60w? Also what settings are you using?

Hi! Where did you purchase the small level?

do a Daddy in the streets!

😂

I'm torn between Monport and the slightly more expensive omtech. I have a diode that I do leather hat patches with and it is time for an upgrade. I can't justify (or afford for that matter) a Thunder, Boss, Epilog, etc...I see horror stories for both Monport and omtech on their FB groups, but your videos have given me some assurance lol..thanks for the videos!!

How long did the tumbler take bud? I'm torn between the 60watt and 80watt.

Nice

Full video?

Will you do my order #2872

Why is it 150 it’s probably 30 in wood and 20 in paint?

It looks so good my brothers name is Liam lol

People who bitch about the cost of custom wood working aren't worth getting business from anyway. They are unreasonable

Great video!

I love you Wowwy Too cute!

🤩✅✅✅

😍❤️💙🤍 Awesome work!

❤💙🤍 In love with this piece!!

Walmart doesn't charge 3x, it's more like 8!

What did you do to the back side?